Instagram AmazingRibs Facebook AmazingRibs X - Meathead Pinterest AmazingRibs Youtube AmazingRibs
BBQ Stars

Welcome!


This is a membership forum. Guests can view 5 pages for free. To participate, please join.

[ Pitmaster Club Information | Join Now | 30 Day Trial | Login | Contact Us ]

Only 4 free page views remaining.

Announcement

Collapse
No announcement yet.

Need stainless ideas...

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Need stainless ideas...

    These are the rods that we hang our sausage on in my vertical smoker. The slots in the smoker that the rods fit in create approx. 3/8" of a gap between the rods.

    I need something to fit in this gap to prevent the rods from closing in on each other when we drape the sausage.

    I would prefer to weld something I can place on there, so that I can just remove it when we go to clean them up and what not.

    I almost welded some stainless pins, stainless angle iron, to the rods. Been wracking my brain over this.

    Click image for larger version

Name:	20261030_230449.jpg
Views:	90
Size:	5.22 MB
ID:	1897686

    #2
    SS tubing or conduit with an I.D. to fit snugly over the rods and an O.D. to fit (without too much slop) into the slots?

    Even easier … just find yourself some larger diameter SS rods to fit the existing slots?
    Last edited by MBMorgan; October 30, 2026, 11:11 PM.

    Comment


    • Jerod Broussard
      Jerod Broussard commented
      Editing a comment
      I think larger diameter rods would be worse since they wouldn't seat as far down into the slots as these. I like the conduit idea. Thanks, never crossed my mind and it should work.

    • Jerod Broussard
      Jerod Broussard commented
      Editing a comment
      Think I'm with going with a "sawtooth" design mentioned below. Finding stainless tubing that I can weld with a 309 electrode is not really practical. If I had a TIG set up it would be doable. Thanks for the ideas. Something I can consider down the road

    #3
    What ^ said, but could you cut it have and tack to the smoker to drop rods into?

    Comment


    • Jerod Broussard
      Jerod Broussard commented
      Editing a comment
      Not really. I load them up prior to placing in the smoker.

    #4
    Jerod, I have not run your exact smoker, so take this as research rather than firsthand use, but a removable spacer comb looks like a clean fit for what you described. Take a strip of 304 stainless flat bar, 1/8 inch thick and about 1 inch wide, long enough to span all the rods, and cut teeth along one edge that drop into the gaps between the rods. Size each tooth a touch under the 3/8 inch gap, say 11/32 inch wide and about 5/8 inch deep, spaced at your rod pitch, which is rod diameter plus that 3/8 inch gap. Lay one comb across the rods about 3 inches in from each end, teeth down. The teeth act as spacers so the rods cannot close in on each other, and since the combs sit on the loaded rods before they go into the smoker, they work with your loading method and just lift off for cleanup.

    If cutting teeth is a pain, build the same thing by welding short pins under a flat bar. Use 3/8 inch diameter 304 rod cut into 5/8 inch stubs and weld one stub under the bar at each gap position. A short piece of 1/4 inch rod welded across the middle of the top makes a handle you can grab with a glove or tongs.

    Two things the research kept pointing to. First, stay with 304 stainless and stainless filler for anything in the food zone, and skip galvanized steel entirely. Second, at sausage smoking temperatures around 180 to 225F warping is not really a concern, but 1/8 inch thickness still matters so the teeth stay straight after repeated handling. If you test one comb first, put it near the end where you load and check how the spacing holds before making the second one.

    Comment


    • Jerod Broussard
      Jerod Broussard commented
      Editing a comment
      What is the best way to cut my gaps out to create my teeth? And yes, stainless all the way. 1/8"/11 gauge is my friend. What I'm most familiar with.

      And I'm going with angle iron. That way I'll have one size laying flat against the bars.

    #5
    Thanks SundaySmokeSignal I gots the stainless marked and ready for the new cutting wheels. I need 8 pieces.

    Click image for larger version

Name:	20261107_213357.jpg
Views:	27
Size:	3.93 MB
ID:	1899890

    Comment

    Announcement

    Collapse
    No announcement yet.
    Working...
    X
    false
    0
    Guest
    Guest
    500
    ["membership","help","nojs","maintenance","shop","reset-password","authaau-alpha","ebooklogin-start","alpha","start"]
    false
    false
    Yes
    ["\/forum\/free-deep-dive-guide-ebook-downloads","\/forum\/free-deep-dive-guide-ebook-downloads\/1157845-paid-members-download-your-6-deep-dive-guide-ebooks-for-free-here","\/forum\/the-pitcast","\/forum\/national-barbecue-news-magazine","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/bbq-news-magazine-2019-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/bbq-news-magazine-2020-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/bbq-news-magazine-2021-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/bbq-news-magazine-2022-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/current-2023-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/current-2024-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/current-2025-issues","\/forum\/national-barbecue-news-magazine\/national-barbecue-news-magazine-aa\/current-2026-issues","\/forum\/bbq-stars","\/forum\/bbq-stars\/tuffy-stone","\/forum\/bbq-stars\/meathead","\/forum\/bbq-stars\/harry-soo","\/forum\/bbq-stars\/matt-pittman","\/forum\/bbq-stars\/kent-rollins","\/forum\/bbq-stars\/dean-fearing","\/forum\/bbq-stars\/tim-grandinetti","\/forum\/bbq-stars\/kent-phillips-brett-gallaway","\/forum\/bbq-stars\/david-bouska","\/forum\/bbq-stars\/ariane-daguin","\/forum\/bbq-stars\/jack-arnold","\/forum\/free-deep-dive-guide-ebook-downloads"]
    /forum/free-deep-dive-guide-ebook-downloads
    7