I'm interested in how to what extent other PBC users trim and smoke their briskets. I do a 'backyard trim' similar to what you see on Arnie Tex on YouTube. My questions:
Do others use a similar trim as Jeremy Yoder on Mad Scientist or Bradley over at Chuds BBQ?
Anyone just smoke on the grate? Fat side up or down?
Anyone try the foil boat method?
I'm recovering from rotator cuff surgery and am looking forward to getting back to using my PBC.
I'm not sure if this helps, I have a Traeger, but I always cook with the fat cap down toward the heat source. I personally think this makes for a better presentation and a better smoke ring.
If I remember correctly, Harry Soo has a YouTube video of a brisket cooked on a PBC.
bbq_esq heavy, like Chud's BBQ plus I clean out the fat between the two muscles to some degree.
The Walmart briskets can be a little tough in there with hard fat. I like to keep a little fat on the fat cap side, even the point, up to 1/4".
My toys:
Weber Summit Charcoal Grilling Center (WSCGC) aka Mr. Fancypants
Pit Barrel Cooker (which rocks), named Pretty Baby
Weber Summit S650 Gas Grill, named Hot 'n Fast (used mostly for searing and griddling)
Weber Kettle Premium 22" named Kettle Kid, eager to horn in with more cooks in the future
Camp Chef Somerset IV 4-burner outdoor gas range named AfterBurner due to its 30kBTU burners
Adrenaline BBQ Company Gear:
SnS Low Profile, DnG, and Large Charcoal Basket, for WSCGC
SnS Deluxe for 22" Kettle
Elevated SS Rack for WSCGC
SS Rack for DnG
Cast Iron Griddle
Grill Grate for SnS
Grill Grates: five 17.375 sections (retired to storage)
Grill Grates: six 19.25 panels for exact fit for Summit S650
gasser
Grill Grates for 22" Kettle
2 Grill Grate Griddles
Steelmade Griddle for Summit gas grill
Fireboard Gear:
Extreme BBQ Thermometer Package
Additional control unit
Additional probes: Competition Probes 1" (3) and 4" (1), 3 additional Ambient Probes. 1 additional Food Probe
2 Driver Cables
Pit Viper Fan (to pair with Fireboard Fan Driver Cable)
Pit Viper Fan new design (to pair with Fireboard Fan Driver Cable)
Thermoworks Gear:
Thermapen MK4 (pink)
Thermapen Classic (pink too)
Thermoworks MK4 orange
Temp Test 2 Smart Thermometer
Extra Big and Loud Timer
Timestick Trio
Maverick ET 73 a little workhorse with limited range
Maverick ET 733
Maverick (Ivation) ET 732
Grill Pinz
Vortex (two of them)
18" drip pan for WSCGC
Ceramic Spacers for WSCGC in Kamado Mode: 2 sets each 1/2", 1", 2". The 2" spacers work best with the 18" drip pan. The 1+1/2 inch spacers work best with the 14 inch cake pan.
Two Joule Sous Vide devices
3 Lipavi Sous Vide Tubs with Lids: 12, 18 and 26 quarts
Avid Armor Ultra Pro V32 Chamber Sealer
Instant Pot 6 Quart Electric Pressure Cooker
Instant Pot 10 Quart Electric Pressure Cooker
Charcoal Companion TurboQue
A-Maze-N tube 12 inch tube smoker accessory for use with pellets
BBQ Dragon and Dragon Chimney
Shun Classic Series:
8" Chef Knife
6" Chef's Knife
Gokujo Boning and Fillet Knife
3 1/2 inch Paring Knife
Thomassen , I trim brisket packers to about 1/4 inch fat and keep the point and flat together, hanging point end up on the PBC until time to wrap when it goes to the grate to finish up.
Haven't tried the boat method yet, but I'd like to.
I hope you're recovering well from your surgery and are soon able to start slinging charcoal bags and briskets around with ease. Best wishes for that.
1. Trim fat cap to about 1/4”-1/2”.
2. On grate, fat cap down.
3. Place a wood chunk under center of the fat cap. The wood pushes the center of the meat up so that there is no pooling of juices on top of the meat, thus retarding bark formation and smoke adherence.
4. Only spritze after rub has set, or you’ll wash off the rub.
I usually separate the point and the flat. They cook at different rates and I find that I can get a better over all cook that way.
I trim the point all the way down to the meat. There is plenty of fat in the meat and there really is not need to for the extra fat.
The flat gets trimmed down to about 1/4-1/2 inch of fat. I like to leave a good band of fat, as it tends to be a little drier in the flat.
I always hang my briskets so the question of fat cap up or down is redundant in my case.
I am not a big wrap guy or boat guy. I let the meat cook unwrapped until I have the color I like. That is usually at about 185 F or so. AT that point, I will wrap it up just to push it through the to the end of the cook. I love to have that nice bark developed, I think the boat and wrapping early methods hinders this process.
I did it on a recent one for the first time. I liked the result, though the flat was still a bit dry. It was a choice packer, not prime. I liked how the bark turned out vs a full wrap. I have never tried butcher paper. I think my biggest takeaways from the last cook were (1) foil boat (2) SPG rub and (3) loooong heated rest. I held mine for like 15 hours between the oven/faux cambro.
I have done foil boats on my Yoder, and they have come out moist, barky and delicious.
Since I am new to Pit barrels(started July 4th this year) I have only did a small brisket on the PBC, just to try it. I wrapped in foil. Everyone liked it.
Comment